|
|
|
www.dcgraves.com |
 |
|
|
|
|
E-Mail: sales@dcgraves.com |
|
|
|
www.dcgraves.com |
|
|
|
|
|
E-Mail: sales@dcgraves.com |
|
Back To Lift Table - Index | Back To Home Page |
|
Lift Table Accessories Page |
|
Motor / Hydraulic Options |
|
| Description | Price |
| Convert From 1.5 HP Three Phase To 1 HP Single Phase | No Charge |
| Convert From 1 HP Single Phase To 1.5 HP Three Phase (208,230 or 460 volt) | $150.00 |
| Convert To 1.5 HP Three Phase External Power Unit (includes transformer for low voltage control, 6' of hose and a mounting stand), (208,230 or 460 volt) | $125.00 |
| Convert To 5 HP Three Phase External Power Unit (includes transformer for low voltage control, 6' of hose and a mounting stand), (208,230 or 460 volt) | $730.00 |
| Convert To 1.5 HP Three Phase (575/3/60) | $150.00 |
| Air Motors | call |
| Custom Designed | call |
| Low Temp Oil | $365.00 |
| Fire Resistant Hydraulic Fluid, water-glycol fluids are fire resistant, non-explosive and non-toxic. Approved by Factory Mutual Insurance Engineering Laboratories | $180.00 |
|
Back To Lift Table - Index | Back To Home Page |
|
Electrical Options |
||
| Description | Price | |
| Hand Operated NEMA 4, weather resistant control with an 8' cord. | Substitute for NEMA 12 Hand | $110.00 |
| Additional Controller | $315.00 | |
| Hand Operated NEMA 4, weather resistant control with an 20' cord. | Substitute for NEMA 12 Hand | $160.00 |
| Additional Controller | $360.00 | |
| NEMA 1 Foot Control, foot operated control. | Substituted for NEMA 12 Hand | $75.00 |
| Additional Controller | $400.00 | |
| Wall Mounted-Control | call | |
| Limit Switch, limits the vertical travel of the scissor lift. | $210.00 | |
| Pedestal-Mounted Controls, NEMA 12 controller mounted on a rugged steel stand with momentary push buttons | $495.00 | |
|
Back To Lift Table - Index | Back To Home Page |
| Mechanical Options | ||
| Description | Price | |
| Oversized Platform, platforms can be increased in width and length up to additional 24". Side and end load capacities are de-rated 2% per inch of increase and oversized models must be lagged to the floor. | $295.00 | |
| Platform with Beveled Edges (scissor lifts only), welded at 30 degree angles, increases the standard platform by 4" on all sides. | $545.00 | |
| Electro-Mechanical Toe Guard (scissor lifts only), mounted to the under side of the platform, adds 3" on all sides. | $620.00 | |
| Lifting Eyes (scissor lifts only), provided for installation and transporting of unit with a sling or lifting chain | $160.00 | |
| Pit Mounted Units (scissor lifts only), for ground level applications require either a Platform with Beveled Edges or Electro-Mechanical Toe Guards. Lifting Eyes required for installation and External Motor recommended. |
See Individual Required Options. |
|
| Portable Units (scissor lifts only), wheeled dolly handle and two 5" fixed wheels (specify side or end mounting) for moving empty lifts. Overall lowered height is not changed when unit is in an operating position. | XL Models | $335.00 |
| X3W & X4W Models | $385.00 | |
| Oversized Platforms | call | |
| Transportable Units (scissor lifts only), 6" steel casters, two fixed and two swivel, and a floor lock mounted underneath base frame. Adds 10.25" to the lowered height. |
XL Models |
$535.00 |
| X3W & X4W Models | $585.00 | |
| Oversized Platforms | call | |
| V Grooved Wheels, 5" steel wheels for Transportable Units only, sold per pair. | All Units | $160.00 |
| Fork Pockets (scissor lifts only), used for moving scissor lifts between work stations. | All Units | Call |
| Ball Transfer Tops, for multi directional movement of work loads, available for all load weights. Adds 2" to overall lowered height. | All Units | Call |
| Turntables, constructed of 1/2" steel plate and mounted on a 24" x 24" base plate equipped with a pivot pin and four 1 3/4 cam followers. Base has mounting holes for lagging unit to table top, floor stand or directly to the floor. Capacities conform to desired work load. Note: Turntables add 2 3/4" to overall height. Custom designs available | 36" round, shipping weight 200 lbs. | call |
| 36" square, shipping weight 225 lbs. | call | |
| 48" round, shipping weight 350 lbs. | call | |
| 48" square, shipping weight 380 lbs. | call | |
| Detent Stops, spring activated stops for a Turntable, standard stops positioned at 90 degree increments | For all turntables above | $170.00 |
| Conveyor Top, mounted to the lift table platform these 1.9" diameter rollers on 3" center have a 1000 lb capacity per linear foot. Adds 4" to overall height. Custom sizes and designs available | 24" x 36" platform | call |
| 24" x 48" platform | call | |
| 24" x 64" platform | call | |
| Custom Sizes | call | |
| Conveyor Sides, used to retain product on conveyor tops, recommend on all Transporting Units. | Fixed 3" sides | call |
| Movable 3" sides | call | |
| Optional Top Material, for special handling of loads, v tops, aluminum material, stainless steel, diamond plate, etc. | call | |
| Accordion (Bellow) Skirts, designed to cover to scissor leg assembly of the lift table. | XL 24 Series | $430.00 |
| XL36 Series | $680.00 | |
| XL48 Series | $1025.00 | |
| Other Models | call | |
|
|
|
Back To Lift Table - Index | Back To Home Page |
